PS/2 Form Factor, Redundant 1+1 power supply, AC Input

MRT-6300P

INPUT CHARACTERISTICS:
VOLTAGE: 90 - 264VAC FREQUENCY: 47 – 63 Hz.
INPUT CURRENT: 6.0 / 3.0A FOR 115 /230 VAC
INRUSH CURRENT:
50A / 70A MAX. FOR 115 / 230 VAC PER MODULE

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. (P-P)
OUTPUT VOLTAGE	MIN.[A]	MAX.[A]	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. (P-P)
5V	1.0	25	±5%	±1%	50mV
12V	2	16	±6%	±1%	120mV
-5V	0.05	0.5	±10%	±1%	120mV
-12V	0.05	0.5	±10%	±1%	150mV
3.3V*	1.0	20	±5%	±1%	50mV
+5VSB	0.1	1.5	±5%	±1%	50mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 35A

(2) TOTAL +5V AND +3.3V AND +12V POWER NOT EXCHEED 285W

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40⁰C, STORAGE -20⁰C--- 70⁰C

HOLD UP TIME: 12 ms MINIMUM AT FULL LOAD & 90 VAC INPUT-VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 MINUTE

INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE

EFFICIENCY: 63% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110 ~ 160% MAX.

OVER VOLTAGE PROTECTION: +5V -- 5.7V ~ 6.5V; +3.3V - 3.9V ~ 4.3V;

12V 13.3V ~14.3V

OVER CURRENT PROTECTION : 5V,12V,3.3V 130% +/-20% AT FULL LOAD

-5V,-12V SHORT CIRCUIT

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: MEET UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

DIMENSION: 185(D) x 150 (W) x 86(H) mm

REMOTE ON / OFF CONTROL

FORM FACTOR PS2+
2U AC Input

MODEL PSL-6600P
INPUT CHARACTERISTICS:
VOLTAGE: 90 ~ 264 VAC FULL RANGE
FREQUENCY: 47~ 63 HZ
INPUT CURRENT: 10.0 A ( RMS ) FOR 115VAC, 5.0 A ( RMS ) FOR 230 VAC
INRUSH CURRENT:
65 A MAX. FOR 115 VAC,

125 A MAX. FOR 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. [P-P]
OUTPUT VOLTAGE	MIN(A).	MAX(A)	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. [P-P]
+5V	5	50	± 5%	± 1%	60mV
+12V	2.5	25	± 5%	± 1%	100mV
-5V	0	0.8	± 5%	± 1%	120mV
-12V	0	1.0	± 5%	± 1%	150mV
+3.3V	1.0	40	+5, -3%	± 1%	60mV
+5VSB	0.1	2	± 5%	± 1%	60mV

** TOTAL OUTPUT POWER NOT EXCEED 600W

*** WHEN IT PERFORMS CROSS REGULATION TEST, IT IS REQUESTED TO SET THE

HIGHER OUTPUT CHANNEL AT 90% MAX. OF IT’S SPEC. AND THE LOWER OUTPUT

CHANNELS AT 20% MAX. THEIRS.

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C --- 40⁰C,

STORAGE -20⁰C --- 80⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 70% TYPICAL

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110 ~ 160%

OVER VOLTAGE PROTECTION: +5Và5.7 ~ 6.5V, 3.3V à3.9 ~ 4.3V, 12Và13.6 ~15V

SHORT CIRCUIT PROTECTION: SHUTDOWN AND LATCH

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE SENSING ON 3.3V DESIGN

REMOTE ON / OFF CONTROL

MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)

COOLING: ONE 80mm DC FAN

DIMENSION: 220 (D) x 150 (W) x 86 (H) mm (STRETCH PS/2)

12C FEATURES (OPTIONAL)

The description stated herein is subject to change without prior notice.

PS/2 Form Factor
AC Input

AP2 SERIES

INPUT CHARACTERISTICS:
VOLTAGE: 90 - 132 VAC / 180 -
264VAC SWITCHABLE
FREQUENCY: 47 ~ 63HZ
INPUT CURRENT:
7.0 / 10.0A (RMS) A FOR 115 VAC
3.5 / 5.0 (RMS) A FOR 230 VAC
INRUSH CURRENT:
40A / 50A MAX. FOR 115 VAC
80A/ 100A MAX. FOR 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		OUTPUT VOLTAGE REGULATION		OUTPUT RIPPLE &
OUTPUT VOLTAGE	MIN(A).	MAX(A)	LOAD	LINE	NOISE MAX. [P-P]
5V	3.0	16~30/24~30	±5%	±1%	50mV
12V	0.5	10/14	±6%	±1%	100mV
-5V	0	1	-16%~10%	±1%	150mV
-12V	0	1	±10%	±1%	150mV
3.3V*	1.0	7~28/20~28	±2%	±1%	50mV
+5VSB	0	1.5	±5%	±5%	50mV

* MANUFACTURER SET AT 3.45
** N / N: 300 / 400W
*PFC Optional

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 50⁰C, STORAGE -20⁰C--- -----80⁰C
TRANSIENT RESPONSE: OUTPUT VOLTAGE RETURNS IN LESS THAN ----1 ms -MAX. FOLLOWING 50% LOAD CHANGE

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT ------------VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

HUMIDITY: 5 ~ 95% RH

EFFICIENCY: 60% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

VER LOAD PROTECTION: 110 ~ 150% MAX.

VER VOLTAGE PROTECTION: +5V -- 5.5V ~ 7.0V; +3.3v - 4.0V ~ 5.0V

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2, TUV IEC 950

DIMENSION: 150(D) x 140 (W) x 86(H) mm (PS/2)

REMOTE ON / OFF CONTROL
TEL UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / NEABLE ALL THE OUTPUT VOLTAGE ( EXCLUDE +5V STANDBY ),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

AVAILABLE MODELS:

MODEL/NO AP2-5300F-RV2S AP2-5300FA-RV2S AP2-5400F-RV2S AP2-5400FA-RV2S AP2-5300F-RV2S AP2-6350F-2S

WATTS 300 300 400 400 300 350

5V 16-30 16-30 24-30 24-30 60-30 20-30

12V 10 10 14 14 10 12

-5V 1 1 1 1 1 1

-12V
1 1 1 1 1 1

+3.3V 7-28 7-28 20-28 20-28 7-28 12-28

+5VSB 1.5 1.5 1.5 1.5 1.5 1.5

UL

CUL

CSA

TUV

VDE

NEMKO

SEMKO

FIMKO

DEMKO

CB

CE

The description stated herein is subject to change without prior notice.

PS/2 Form Factor
DC Input

DB2 Series

GENERAL INFORMATION

INPUT VOLTAGE:-20 VDC TO -28VDC

INPUT CURRENT:7A AT -24VDC INPUT

INRUSH CURRENT :LESS THAN 5A AT -24VDC INPUT

INPUT PROTECTION :AGAINST WRONG POLARITY

SHORT PROTECTION : SHUT DOWN

OVER VOLTAGE PROTECTION : CROWBAR, TRIP POINT 6.0V TO 7.0VDC

OPERATING TEMPERATURE : 10⁰C50⁰C

STORAGE TEMPERATURE : -20⁰C+75⁰C

SAFETY STANDARD : DESIGNED TO MEET THE REQUIREMENTS OF IEC950.

UL1950. CSA22.2

INPUT CONNECTOR : 3 POSITION TERMINAL BLOCK

POWER GOOD/ FAIL SIGNALS : BUILT-IN

OVERLOAD PROTECTION : SHUT DOWN (POWER LIMIT)

EMI : DESIGNED TO MEET THE REQUIREMENTS OF FCC. CISPR22.

OUTPUT CHARACTERISTICS(25⁰C):

OUTPUT VOLTAGE	LOAD[A] RATE		LOAD REGUL-ATION	LINE REGUL-ATION	P.G SIGNAL	POWER FAIL SIGNAL	POWER EFFICI-ENCY
	MIN	MAX
+5 V	2.0	16	+5% ~ -5%	< ±1%	MIN 100ms max. 500ms.	1ms	60% min
+12 V	0.5	8	+8% ~-5%
-5 V	0	3	+10% ~ -10%
-12 V	0	1.0	+5% ~ -5%
+3.3 V	1	10	±5%
+5VSB	0	1.2	±5%

*PFC/AVS OPTIONAL

The description stated herein is subject to change without prior notice.

1+1 Redundant Power Supply
AC Input

RHD-6400P
INPUT CHARACTERISTICS:
VOLTAGE: 100 ~ 240 VAC (WITH ±10% TOLERANCE)
FREQUENCY: 47 ~ 63HZ
INPUT CURRENT:
2.5A / 1.5A PER UNIT (PARALLEL) 7.0A / 4.0A (ONE POWER)
INRUSH CURRENT:
65A MAX. FOR 110 VAC
125A MAX. FOR 220VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. (P-P)
OUTPUT VOLTAGE	MIN.[A]	MAX.[A]	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. (P-P)
+5V	5.0	35	±5%	±1%	60mV
-5V	0.0	0.8	±5%	±1%	100mV
+12V	2.5	20	±5%	±1%	100mV
-12V	0.0	1.0	±6%	±1%	100mV
+3.3V	0.0	28	±5%	±1%	60mV
+5VSB	0.0	2.0	±7%	±1%	60mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 50A

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0℃ -- 40℃ ; STORAGE –20℃ -- 80℃

TRANSIENT RESPONSE: OUTPUT VOLTAGE RETURNS IN LESS THAN 1 ms MAX.

FOLLOWING A 50% LOAD CHANGE

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1800 VAC FOR 1 MINUTE

INPUT TO FRAME GROUND 1800 VAC FOR 1 MINUTE

HUMIDITY: 10 ~ 90% RH

EFFICIENCY: 68% TYPICAL, AT 115V, FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110 ~ 150% MAX.

OVER VOLTAGE PROTECTION: +5V 5.7V ~ 6.5V, 3.3V: 3.9V ~ 4.3V, +12V: 13.6V ~ 15V

OVER CURRENT PROTECTION: : +5V: 44A ~ 60A, +12V: 29.7A ~ 40.5A, +3.3V: 33A ~ 45A

ALARM METHOD: 1. AUDIO ALARM, 2. FAULT LED, 3. POWER DEFECTIVE, 4. AC IN DEFECTIVE, 5. EACH POWER MODULE’S IN SIGNAL

FCC CLASS B, CISPR22 CLASS B

SAFETY: UL / CSA / TUV APPROVAL

HOT-SWAPPABLE / HOT-PLUGGABLE CAPABILITY

DIMENSION: REFER TO THE DRAWING

REDUNDANCY: BALANCE SHARE LOAD METHOD

REMOTE ON/OFF: OPERATE BY A REMOTE (SELV) SIGNAL

5VSB STANDBY VOLTAGE: A LOW CURRENT CONTINUOUS 2A SOURCE AT +5V, ALWAYS ENABLE, CAN NOT BE REMOTE OFF

The description stated herein is subject to change without prior notice.

1+1 Redundant Power Supply
AC Input

RHD-6460P
INPUT CHARACTERISTICS:
VOLTAGE: 100 ~ 240 VAC (WITH ±10% TOLERANCE)
FREQUENCY: 47 ~ 63HZ
INPUT CURRENT:
2.5A / 1.5A PER UNIT (PARALLEL) 7.0A / 4.0A (ONE POWER)
INRUSH CURRENT:
65A MAX. FOR 110 VAC
125A MAX. FOR 220VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. (P-P)
OUTPUT VOLTAGE	MIN.[A]	MAX.[A]	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. (P-P)
+5V	5.0	40	±5%	±1%	60mV
-5V	0.0	0.8	±5%	±1%	100mV
+12V	2.5	27	±5%	±1%	100mV
-12V	0.0	1.0	±6%	±1%	100mV
+3.3V	0.0	30	±5%	±1%	60mV
+5VSB	0.0	2.0	±7%	±1%	60mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 50A

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0℃ -- 40℃ ; STORAGE –20℃ -- 80℃

TRANSIENT RESPONSE: OUTPUT VOLTAGE RETURNS IN LESS THAN 1 ms MAX.

FOLLOWING A 50% LOAD CHANGE

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1800 VAC FOR 1 MINUTE

INPUT TO FRAME GROUND 1800 VAC FOR 1 MINUTE

HUMIDITY: 10 ~ 90% RH

EFFICIENCY: 68% TYPICAL, AT 115V, FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110 ~ 150% MAX.

OVER VOLTAGE PROTECTION: +5V 5.7V ~ 6.5V, 3.3V: 3.9V ~ 4.3V, +12V: 13.6V ~ 15V

OVER CURRENT PROTECTION: : +5V: 44A ~ 60A, +12V: 29.7A ~ 40.5A, +3.3V: 33A ~ 45A

POWER FACTOR CORRECTOR: MEET IEC-1000-302 CLASS D (ACTIVE PFC)

ALARM METHOD: 1. AUDIO ALARM, 2. FAULT LED, 3. POWER DEFECTIVE, 4. AC IN DEFECTIVE, 5. EACH POWER MODULE’S IN SIGAL

FCC CLASS B, CISPR22 CLASS B

SAFETY: UL / CSA / TUV APPROVAL

HOT-SWAPPABLE / HOT-PLUGGABLE CAPABILITY

DIMENSION: REFER TO THE DRAWING

REDUNDANCY: BALANCE SHARE LOAD METHOD

REMOTE ON/OFF: OPERATE BY A REMOTE (SELV) SIGNAL

5VSB STANDBY VOLTAGE: A LOW CURRENT CONTINUOUS 2A SOURCE AT +5V, ALWAYS ENABLE, CAN NOT BE REMOTE OFF

The description stated herein is subject to change without prior notice.

1+1 Redundant Power Supply
AC Input

ARI SERIES
INPUT CHARACTERISTICS:
VOLTAGE:
90 - 132 VAC / 180 - 264 VAC SWITCHABLE
FREQUENCY: 47 - 63 Hz
INPUT CURRENT:
5.0A / 2.5A PER UNIT (PARALLEL)
INRUSH CURRENT:
50A / 100A MAX. FOR 115 / 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT			REGULATION
OUTPUT VOLTAGE	MIN.[A]	MAX.[A]	PEAK(A)	LOAD.	LINE	OUTPUT RIPPLE & NOISE MAX. (P-P)
5v	7.0	20~36	40	±5%	±1%	60mV
12v	2.5	17	20	±8%	±1%	120mV
-5v	0	0.8	1	±10%	±1%	120mV
-12v	0	0.8	1	±10%	±1%	150mV
3.3V*	3.0	0~25	30	±5%	±1%	60mV
+5VSB	0	1.0	1.2	±5%	±1%	50mV

* MANUFACTURER SET AT 3.45 V

TOTAL POWER OF +5V AND +3.3V SHALL NOT EXCEED 180W.

*AVS OPTIONAL

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40

TRANSIENT RESPONSE: OUTPUT VOLTAGE RETURNS IN LESS THAN 1 ms

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 65% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 130+/- 20%

OVER VOLTAGE PROTECTION: +5V6.0V ~ 7,3.3V4.0~4.5V(EACH POWER UNIT)

OVER CURRENT PROTECTION: SHORT CIRCUIT (EACH POWER UNIT)

ALARM METHOD: AUDIO ALARM, FAULT LED, POWER DEFECTIVE SIGNAL

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: MEET UL 1950, CSA 22.2, TUV IEC 950

DIMENSION: ARD: 153(W) x 212(H) x 190(D); ARI: 167(W) x 189(H) x 190 (D)

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),

AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,

AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

REDUNDANCY: BALANCED SHARE LOAD

HOT-SWAPPABLE / REDUNDANCY FUNCTION

REMOTE SENSING DESIGN

PASSIVE BACKPLANE DESIGN

CONNECTION: 48 PINS CONNECTOR (EPT PART NO. 109-40064 ON EQUIPMENT)

I²C COMMUNICATION ABILITY

AVAILABLE MODELS:

MODEL/NO	ARI-2300F	ARI-2400F	ARI-4300F	ARI-4400F	ARI-6300F	ARI-6400F
WATTS	300	400	300	400	300	400
5V	36	36	36	36	20-36	20-36
12V	17	17	17	17	17	17
-5V			0.8	0.8	0.8	0.8
-12V			0.8	0.8	0.8	0.8
+3.3V					25	25
+5VSB					1	1
UL
CUL
CSA
TUV
VDE
NEMKO
SEMKO
FIMKO
DEMKO
CB
CE

The description stated herein is subject to change without prior notice.

N+1 Redundant Power Supply
AC Input

IRN1-6400F SERIES

INPUT CHARACTERISTICS:
VOLTAGE: 90 -132 VAC / 180 -264VAC
--------- -------SWITCHABLE
FREQUENCY: 47 - 63 Hz
INPUT CURRENT:
5.0A / 2.5A PER UNIT
(PARALLEL)
INRUSH CURRENT:
50A / 100A MAX.
FOR 115 / 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT
VOLTAGE OUTPUT CURRENT REGULATION

MIN.[A] MAX.[A] RANGE MIN NOM MAX OUTPUT
RIPPLE & NOISE
MAX. (P-P)

5v

7.0

20~36

±5%

+4.75

+5.00

+5.25

60mV

12v

2.5

18

±5%

+11.04

+12.00

+12.96

120mV

-5v

0

0.8

±5%

-4.50

-5.00

-5.50

120mV

-12v

0

0.8

±5%

-10.80

-12.00

-13.20

150mV

3.3V*

3

0~25

±5%

+3.13

+3.30

+3.47

60mV

+5VSB

0

1.0A

±5%

+4.75

+5.00

+5.25

50mV

* MANUFACTURER SET AT 3.45
TOTAL POWER OF +5V AND +3.3V SHALL NOT EXCEED 180W.
*PFC/AVS OPTIONAL

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40⁰C, STORAGE -20⁰C--- 80⁰C

TRANSIENT RESPONSE: OUTPUT VOLTAGE RETURNS IN LESS THAN 1 ms

MAX. FOLLOWING 50% LOAD CHANGE

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

HUMIDITY: 10 ~ 90% RH

EFFICIENCY: 65% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110 ~ 150% MAX.

OVER VOLTAGE PROTECTION: +5V 6.0V ~ 7.0V (EACH POWER UNIT)

OVER CURRENT PROTECTION: SHORT CIRCUIT (EACH POWER UNIT)

ALARM METHOD: AUDIO ALARM, FAULT LED, POWER DEFECTIVE SIGNAL

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: EACH POWER UNIT MEET UL 1950, CSA 22.2, TUV IEC 950

DIMENSION: 150 x 150 x 86 mm

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),

AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,

AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

REDUNDANCY: BALANCED SHARE LOAD METHOD

The description stated herein is subject to change without prior notice.

N+1 Redundant PowerSupply
DC Input

MDN1- 6230F SERIES
INPUT CHARACTERISTICS:
VOLTAGE:DC-42~-56
FREQUENCY: 47~63HZ
INPUT CURRENT:
9A MAX.FOR EACH POWER UNIT
INRUSH CURRENT:
10A (RMS) FOR -42VDC

OUTPUT CHARACTERISTICS:
TOTAL POWER:230W

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. [P-P]
OUTPUT VOLTAGE	MIN.	MAX.	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. [P-P]
5V	2.5	20	±5%	±1%	50mV
12V	0.5	0.5	±6%	±1%	100mV
-5V	0	8	±10%	±1%	100mV
-12V	0	0.5	±10%	±1%	120mV
3.3V	0	10	±5%	±1%	50mV
+5VSB	0	1.2	±5%	±1%	50mV

*PFC/AVS OPTIONAL

SPECIFICATION:

TEMPERATURE RANGE : OPERATING 0⁰C ~50⁰C

HOLD UP TIME:16mS MINIMUM AT FULL LOAD & NOMINAL INPUT VOLTAGE

DIELECTRIC WITHSTAND:
INPUT/OUTPUT 1500 VAC FOR 60 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 60 SECOND

EFFICIENCY:66% TYPICAL¡AAT FULL LOAD

POWER GOOD SIGNAL:ON DELAY 100mS TO 500mS OFF DELAY 1 ms

OVERLOAD PROTECTION:130+/-20%

OVER VOLTAGE PROTECTION:+5V5.74V ~7V ,12V14.3V ~15.6V

SHORT CIRCUIT PROTECTION: Shut down and latch off

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2 MP/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILLDISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY)AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

N + 1 REDUNDANCY FUNCTION

HOT-SWAPPABLE FUNCTION

CURRENT / BALANCE LOAD SHARING DESIGN

3.3V / 5V REMOTE SENSING

ISOLATION: BUILT-IN IN EACH POWER MODULE

COOLING: TWO 40mm DC FANS IN EACH MODULE & TWO 80mm DC FANS IN

POWER CHASSIS

DIMENSION: 160 (D) x 142 (W) x 42.5(H) mm

CONNECTION: 48 PINS CONNECTOR (EPT PART NO. 109-40064 OR EQUIVALENT)

AVAILABLE MODELS:

MODEL/NO MDN2-
6230F MDN3-
6460F MDN4(H)
6690F MDN5-
6920F MDN6(H)
6B50F

WATTS 230 460 690 920 1050

5V 20 40 60 80 100

12V 8 16 24 32 40

-5V 0.5 0.5 0.5 0.5 0.5

-12V
0.5 0.5 1 1.5 2

+3.3V 10 20 30 40 50

+5VSB 1 1.2 1.6 2.1 2.5

UL

CUL

CSA

TUV

VDE

NEMKO

SEMKO

FIMKO

DEMKO

CB

CE

The description stated herein is subject to change without prior notice.

N+1 Redundant Power Supply
Dual Input

MUH6/MUN6-6620F SERIES
INPUT CHARACTERISTICS:
VOLTAGE: DC-42 V ~-56 V ; AC 90 ~ 132 V OR 180 ~ 264 V ( SWITCHABLE )
INPUT CURRENT:
27A (RMS) FOR- 42VDC; 18.0A / 9A (RMS) FOR 115/230 VAC
INRUSH CURRENT
( POWER MODULE )
10 A MAX. FOR -42 VDC INPUT; 25 A MAX. FOR 115 VAC INPUT

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		OUTPUT VOLTAGE REGULATION			OUTPUT RIPPLE &
	MIN(A).	MAX(A)	LOAD	LINE	NOISE MAX. [P-P]
5V	7.5	60	±5%	±1%	50mV
12V	3.0	24	±6%	±1%	100mV
-5V	0	0.5	±10%	±1%	100mV
-12V	0	2.0	-10%~+11%	±1%	120mV
3.3V	1.5	30	±5%	±1%	50mV
+5VSB	0	1.6	±5%	±1%	50mV

*PFC/AVS OPTIONAL

REMARKS:

TOTAL OUTPUT 620W

DUAL INPUT SOURCES ( DC ¡V48V & AC )

TEMPERATURE RANGE: OPERATING 0⁰C --- 50⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL AC INPUT VOLTAGE

1.6 ms MINIMUM AT FULL LOAD & NORMAL DC INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 66% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 130 +/- 20%

OVER VOLTAGE PROTECTION: +5V5.5V ~ 7V, 12V13.5V ~ 15.5V,

3.3V 3.76 ~ 4.3V, 5VSB 5.74 ~ 7V

SHORT CIRCUIT PROTECTION: EACH CHANNEL

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),

AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,

AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

N + 1 REDUNDANCY FUNCTION ( 3+3 )

HOT-SWAPPABLE FUNCTION

CURRENT / BALANCE LOAD SHARING DESIGN

3.3V / 5V REMOTE SENSING

COOLING: TWO 40mm DC FANS (POWER MODULE); TWO 80mm DC FANS

DIMENSION: 230 (D) x 356 (W) x 139 (H) mm MUH6; 230 (D) x 164 (W) x 288 mm MUN6

CONNECTION: 48 PINS CONNECTOR (EPT PART NO. 109-40064 OR EQUIVALENT)

The description stated herein is subject to change without prior notice.

1U, Redundant 1+1 power supply
AC Input

RIG-6250P

INPUT CHARACTERISTICS:
VOLTAGE: 90 - 264VAC FULL RANGE FREQUENCY: 47 – 63 Hz.
INPUT CURRENT: 6.0 / 3.0A FOR 115 /230 VAC
INRUSH CURRENT:
40A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		OUTPUT VOLTAGE REGULATION		OUTPUT RIPPLE &
OUTPUT VOLTAGE	MIN(A).	MAX(A)	LOAD	LINE	NOISE MAX. [P-P]
+5V	3.0	25	±5%	±1%	50mV
12V	2.0	16	±7%	±1%	100mV
-5V	0.05	0.5	±10%	±1%	120mV
-12V	0.05	0.5	±10%	±1%	150mV
3.3V*	1.0	15	±5%	±1%	50mV
+5VSB	0.1	2.0	±5%	±1%	50mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 28A

(2) TOTAL +5V AND +3.3V AND +12V POWER NOT EXCEED 232W

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40⁰C, STORAGE –20⁰C ~ 70⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & 90 VAC INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 63% TYPICAL AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110 ~ 160% MAX.

OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.3V, 12V à 13.6V ~ 14.5V

SHORT CIRCUIT PROTECTION: SHUT DOWN

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: MEET UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

FAULTY ALARM METHODS : LED, BUZZER, TTL SIGNAL

HOT-SWAPPABLE / HOT-PLUGGABLE 1 + 1 REDUNDANCY FUNCTION

BALANCE LOAD SHARING DESIGN

REMOTE SENSING DESIGN

ISOLATION: BUILT-IN IN THE POWER MODULE

MEET IEC-1000-3-2 CLASS D ( ACTIVE PFC )

DIMENSION: 40.6(H) X 180(W) X 260 (D) mm

COOLING : TWO 40 mm DC FANS

FORM FACTOR
1U AC Input

P1L-6400P
INPUT CHARACTERISTICS:
VOLTAGE: 95 - 264VAC FULL RANGE FREQUENCY: 47 – 63 Hz.
INPUT CURRENT: 6.0 / 3.0A FOR 115 /230 VAC
INRUSH CURRENT:
65A / 125A MAX. FOR 115 / 230 VAC PER MODULE

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		OUTPUT VOLTAGE REGULATION		OUTPUT RIPPLE &
OUTPUT VOLTAGE	MIN(A).	MAX(A)	LOAD	LINE	NOISE MAX. [P-P]
5V	2.0	30	±5%	±1%	50mV
12V	1.0	28	±6%	±1%	120mV
-5V	0	0.5	±10%	±1%	150mV
-12V	0	0.8	±10%	±1%	150mV
3.3V*	1.0	25	±5%	±1%	50mV
+5VSB	0	2.0	±5%	±1%	50mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 50A

(2) TOTAL +5V AND +3.3V AND +12V POWER NOT EXCHEED 400W

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 60% TYPICAL

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 130 +/- 20%

OVER VOLTAGE PROTECTION: +5V à 5.5V ~ 7V, 3.3V à 4.0 ~ 4.5V;

SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: MEET UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V TANDBY), AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE, AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

3.3V / 5V REMOTE SENSING

COOLING: TWO 40mm DC FANS , ONE EXTRA IS OPTIONAL

DIMENSION: 300(D) x 106 (W) x 40.5(H) mm

ACTIVE POWER FACTOR CORRECTION MEET IEC-1000-3-2 CLASS D

240VA SAFETY LIMIT PROTECTION

I²C FEATURE IS OPTIONAL

FORM FACTOR
1U AC Input

P1G- 6305P
INPUT CHARACTERISTICS:
VOLTAGE: 90 ~ 264 VAC FULL RANGE
FREQUENCY: 47 ~ 63 HZ
INPUT CURRENT:
6.0 A ( RMS ) FOR 115VAC
3.0 A ( RMS ) FOR 230VAC
INRUSH CURRENT:
60.0A MAX. FOR 115 VAC
80.0A MAX. FOR 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. [P-P]
OUTPUT VOLTAGE	MIN.[A]	MAX.[A]	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. [P-P]
+5V	3	30	± 5%	± 1%	80mV
+12V	2	16	± 8%	± 1%	120mV
-5V	0.05	0.5	±10%	± 1%	150mV
-12V	0.05	1.0	±10%	± 1%	150mV
+3.3V	1.0	14	± 5%	± 1%	70mV
+5VSB	0.1	1.5	± 5%	± 1%	50mV

REMARKS: THE OUTPUT POWER OF 5V, 3.3V & 12V NOT EXCEED 180 WATTS

THE OUTPUT POWER OF 5V, 3.3V & 12V TOTAL 278 WATTS MAX

TOTAL OUTPUT POWER NOT EXCEED 300 WATTS.

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C --- 40⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 65% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 110% ~ 150%

OVER VOLTAGE PROTECTION: +5Và5.5V ~ 7.0V, 3.3V à4.0V ~ 5.0V

SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL

DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),

AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,

AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

3.3V / 5V REMOTE SENSING

COOLING: ONE 40mm DC FAN

DIMENSION: 205 (D) x 100 (W) x 40.5 (H) mm.

ACTIVE POWER FACTOR CORRECTION : MEET IEC-1000-3-2 CLASS D

The description stated herein is subject to change without prior notice.

1U power supply, AC Input

SIU-6250P

INPUT CHARACTERISTICS:
VOLTAGE: 95 - 265VAC FULL RANGE FREQUENCY: 47 – 63 Hz.
INPUT CURRENT: 6.0A / 3.0A FOR 115 /230 VAC
INRUSH CURRENT:
30A / 60A MAX. FOR 115 / 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		OUTPUT VOLTAGE REGULATION		OUTPUT RIPPLE &
OUTPUT VOLTAGE	MIN(A).	MAX(A)	LOAD	LINE	NOISE MAX. [P-P]
+5V	1.0	21	±5%	±1%	80mV
+12V	0.2	10	±8%	±1%	120mV
-5V	0	0.5	±10%	±1%	150mV
-12V	0	0.8	-10% ~ +10%	±1%	150mV
3.3V*	1.0	14	±5%	±1%	70mV
+5VSB	0	1.5	±5%	±1%	50mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 115W

(2) TOTAL OUTPUT POWER NOT EXCHEED 250W

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 60% TYPICAL

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 130 +/- 20%

OVER VOLTAGE PROTECTION: +5V à 5.5V ~ 7V, 3.3V à 4.0 ~ 4.5V

SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: MEET UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

3.3V / 5V REMOTE SENSING

COOLING: TWO 40mm DC FANS , ONE EXTRA IS OPTIONAL

DIMENSION: 205(D) x 79 (W) x 40(H) mm

ACTIVE POWER FACTOR CORRECTION MEET IEC-1000-3-2 CLASS D

OTHER APPLICATIONS
1U AC Input

MPW SERIES
INPUT CHARACTERISTICS:
VOLTAGE:95 ~ 135 VAC OR 180 ~ 265 VAC AUTO SWITCHING
FREQUENCY:47 ~ 63 HZ
INPUT CURRENT:
6.0 A ( RMS ) FOR 115VAC
3.0 A ( RMS ) FOR 230VAC
INRUSH CURRENT:
30.0A MAX. FOR 115 VAC
60.0A MAX. FOR 230 VAC

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. [P-P]
OUTPUT VOLTAGE	MIN.	MAX.	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. [P-P]
+5V	1.6	16	± 5%	± 1%	80mV
+12V	0.9	9.0	± 8%	± 1%	120mV
-5V	0	0.2	± 10%	± 1%	120mV
-12V	0	0.7	-10%~+10%	± 1%	150mV
+3.3V	1.0	10	± 5%	± 1%	70mV
+5VSB	0.15	1.5	± 5%	± 1%	50mV

*PFC/ABS OPTIONAL

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 10⁰C --- 40⁰C

HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 60% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 130 +/- 20%

OVER VOLTAGE PROTECTION: +5V 5.5V ~ 7V, 3.3V 4.0 ~ 4.5V

SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),

AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,

AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

COOLING: ONE 40mm DC FAN

DIMENSION: 190 (D) x 100 (W) x 40.5 (H) mm

AVAILABLE MODELS:

MPW
-
6150F

MPW
-
6180F

MPW

6200F

MPW

6230F

P1U
-
6150P

P1U

6200P

P1A
-
6200P

P1A

6250P

P1G
-
6250P

P1G

6300P

PHD

6150F

B1U
-
6150F

D1U
-
6150F

D1U

6180F

MODEL

*AC 1U CHASSIS PSU

*DC 1U CHASSIS PSU

WATTS

150

180

200

230

150

200

250

300

150

180

12V

-5V

0.2

0.5

0.2

0.5

0.2

0.5

-12V

0.7

0.5

1.0

+3.3V

+5Vsb

0.72

1.5

0.72

1.5

CUL

CSA

TUV

VDE

DIMENSION (m/m)

L190

X W100 X
H40.5

L190 X W100 X
H40.5

L190

W100

H40.5

L190

W100

H40.5

L190 X W100 X H40.5

L190

W100

H40.5

L190 X W100 X
H40.5

L205 X W100 X
H40.5

L140 X W120 X
H40.5

L190 X W100 X H40.5

The description stated herein is subject to change without prior notice.

OTHER APPLICATIONS
1U DC Input

B1U SERIES

INPUT CHARACTERISTICS:
VOLTAGE: DC-21 V ~ -- 28 V
--------- -------
INPUT CURRENT:
12.0 A ( RMS )
FOR-24 VDC
INRUSH CURRENT:
20 A MAX.

OUTPUT CHARACTERISTICS

OUTPUT VOLTAGE	OUTPUT CURRENT		REGULATION		OUTPUT RIPPLE & NOISE MAX. [P-P]
OUTPUT VOLTAGE	MIN.	MAX.	LOAD	LINE	OUTPUT RIPPLE & NOISE MAX. [P-P]
+5V	1.0	10	± 5%	± 1%	80mV
-5V	0.5	6.0	± 8%	± 1%	120mV
+12V	0	0.5	±10%	± 1%	120mV
-12V	0	1.0	-10%~+10%	± 1%	150mV
3.3V	1.0	10	± 5%	± 1%	80mV
+5VSB	0	1.5	± 5%	± 1%	50mV

REMARKS: +5 V AND + 3.3 V TOTAL OUTPUT MAX. 70 WATTS
*PFC/AVS OPTIONAL

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C --- 50⁰C

HOLD UP TIME: 1.6 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND

INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 60% TYPICAL, AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

OVER LOAD PROTECTION: 130 +/- 20%

OVER VOLTAGE PROTECTION: +5V 5.5V ~ 7V, 3.3V 4.0 ~ 4.5V

SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V

EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B

SAFETY: UL 1950, CSA 22.2 NO/ 950, TUV IEC 950

REMOTE ON / OFF CONTROL

THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),

AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,

AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.

COOLING: ONE 40mm DC FAN

DIMENSION: 190 (D) x 100 (W) x 40.5 (H) mm

INPUT SOURCE CONNECTOR : POSITRONIC BLUE CONNECTOR

AVAILABLE MODELS:

MPW
-
6150F

MPW
-
6180F

MPW

6200F

MPW

6230F

P1U
-
6150P

P1U

6200P

P1A
-
6200P

P1A

6250P

P1G
-
6250P

P1G

6300P

PHD

6150F

B1U
-
6150F

D1U
-
6150F

D1U

6180F

MODEL

*AC 1U CHASSIS PSU

*DC 1U CHASSIS PSU

WATTS

150

180

200

230

150

200

250

300

150

180

12V

-5V

0.2

0.5

0.2

0.5

0.2

0.5

-12V

0.7

0.5

+3.3V

+5Vsb

0.72

1.5

0.72

1.5

CUL

CSA

TUV

VDE

DIMENSION (m/m)

L190

X W100 X
H40.5

L190 X W100 X
H40.5

L190

W100

H40.5

L190

W100

H40.5

L190 X W100 X H40.5

L190

W100

H40.5

L190 X W100 X
H40.5

L205 X W100 X
H40.5

L140 X W120 X
H40.5

L190 X W100 X H40.5

The description stated herein is subject to change without prior notice.

Redundant 1+1, n +1 redundant power supply
AC Input

R3G-6630P

INPUT CHARACTERISTICS:
VOLTAGE: 95 - 264VAC FULL RANGE FREQUENCY: 47 – 63 Hz.
INPUT CURRENT: 6.0A / 3.0A FOR 115 /230 VAC
INRUSH CURRENT:
60A / 80A MAX. FOR 115 / 230 VAC PER MODULE

OUTPUT CHARACTERISTICS:

OUTPUT VOLTAGE	OUTPUT CURRENT		OUTPUT VOLTAGE REGULATION		OUTPUT RIPPLE &
OUTPUT VOLTAGE	MIN(A).	MAX(A)	LOAD	LINE	NOISE MAX. [P-P]
+5V	3.0	60	±5%	±1%	50mV
+12V	2.0	40	±5%	±1%	120mV
-5V	0.05	1.0	±10%	±1%	120mV
-12V	0.05	1.0	±10%	±1%	150mV
3.3V	1.0	40	±5%	±1%	50mV
+5VSB	0.1	2.5	±5%	±1%	50mV

REMARKS:

(1) TOTAL CURRENT OF +5V AND +3.3V : 70A

(2) TOTAL +5V AND +3.3V AND +12V POWER NOT EXCHEED 600W

SPECIFICATION:

TEMPERATURE RANGE: OPERATING 0⁰C--- 40⁰C, STORAGE –20⁰C ~ 70⁰C

HOLD UP TIME: 20 ms MINIMUM AT FULL LOAD & 90 VAC INPUT VOLTAGE

DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND

EFFICIENCY: 63% TYPICAL,AT FULL LOAD

POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms

MODEL/NO	AP2-5300F-RV2S	AP2-5300FA-RV2S	AP2-5400F-RV2S	AP2-5400FA-RV2S	AP2-5300F-RV2S	AP2-6350F-2S
WATTS	300	300	400	400	300	350
5V	16-30	16-30	24-30	24-30	60-30	20-30
12V	10	10	14	14	10	12
-5V	1	1	1	1	1	1
-12V	1	1	1	1	1	1
+3.3V	7-28	7-28	20-28	20-28	7-28	12-28
+5VSB	1.5	1.5	1.5	1.5	1.5	1.5
UL
CUL
CSA
TUV
VDE
NEMKO
SEMKO
FIMKO
DEMKO
CB
CE

MODEL/NO	MDN2- 6230F	MDN3- 6460F	MDN4(H) 6690F	MDN5- 6920F	MDN6(H) 6B50F
WATTS	230	460	690	920	1050
5V	20	40	60	80	100
12V	8	16	24	32	40
-5V	0.5	0.5	0.5	0.5	0.5
-12V	0.5	0.5	1	1.5	2
+3.3V	10	20	30	40	50
+5VSB	1	1.2	1.6	2.1	2.5
UL
CUL
CSA
TUV
VDE
NEMKO
SEMKO
FIMKO
DEMKO
CB
CE