SIMEPROM-02aLV

EPROM simulator 2716 - 27040

simulation EPROM 2716..27040, 85ns
LV EPROM support from 2.5V
output buffer powered from target system
special protection circuits against electrostatic discharge included
dual connection to PC: standard printer port or serial port
easy to use control program, DOS and Windows 95/98/Me/NT/2000/XP compatible
3 years warranty

EPROM simulator

Because simulator are in generally susceptible to damage by ESD (electrostatic discharge), there was developed and build-in into SIMEPROM-02aLV special protection circuit without influence to parameters of simulator. This mean, that simulator SIMEPROM-02aLV is protected either against electrostatic discharge (ESD) and against balancing current that might flow between emulator and target systems.

Quality of SIMEPROM-02aLV and negligible sales returns allows afford nearly lifetime - 3 years - guarantee for him.

Since SIMEPROM-02aLV simulator contains CMOS RAMs, whose contents can be easily changed anytime, it can be replaced obsolete debugging cycle

switching off the target system

removing the EPROM from the socket

EPROM erasing

EPROM programming

inserting EPROM into the socket

switching on the target system
(about 20 minutes)

SIMEPROM-02aLV re-downloading
(about 25 seconds)

In addition, the SIMEPROM-02aLV enables the user forced the RESET signal on a device under development. Thus, a software can be debugged without handling the device.

SIMEPROM-02aLV interfaces with the IBM PC, XT to Pentium Pro, portable or desktop personal computers. Simulators allows you to directly connect to your PC through any standard parallel printer port or through standard (RS232) serial port. In case connection through serial port, SIMEPROM-02aLV is optically isolated from target systems. Using a Y-cable they are possible to connect two SIMEPROM-02aLV simulators on the same parallel port. Generally, on the one PC, it can be connected four SIMEPROM-02aLV simulators.

The SIMEPROM-02aLV simulator is controlled from the PC by the control program, which is common for all of the ELNEC's EPROM simulators. It is easy-to-use nice software with pull-down menu, hot keys and on-line help. The control program find himself type and port of connected simulator. Thus, it's possible connect all types of ELNEC's simulators on the same computer at the same time. User can doing

all necessary functions with simulator (download, RESET control)
with buffer (view, edit, fill, copy, swap, checksum, print)
read/write buffer in binary or wide range of HEX formats.

There are a BAT file version of control program, which can download of simulator content and can change the RESET status. For DOS operating system is available resident version of control program too.

There is available appropriate package convertor PLCC32/DIL32 for work with EPROM in PLCC32.

Specification

Versions

SIMEPROM-02aLV ver. 020/120, equivalent EPROM/EEPROM/PROM 27C020-120ns
SIMEPROM-02aLV ver. 040/85, equivalent EPROM/EEPROM/PROM 27C040-85ns

Supported devices

EPROM/PROM: NMOS/CMOS, family 27xxx and 27Cxxx, from 2KByte (2716) to 512KByte (27040/274001) with 8 bit data bus in DIL or PLCC.
EEPROM: NMOS/CMOS, family 28xxx, 28Cxxx, 27EExxx, from 2KByte (2816) to 512KByte (28040) with 8 bit data bus in DIL or PLCC.
EPROM/PROM/EEPROM from 64KByte to 1MByte with 16 bit data bus in DIL or PLCC (2x SIMEPROM-02aLV with converter DIL40/DIL2x32 W-EPROM)

Compatibility

response on the address changed: max. 85 ns (max. 120 ns)
response on the CE\ signal going to L: max. 85 ns (max. 120 ns)
response on the OE\ signal going to L : max. 45 ns (max. 60 ns)
response on the either OE\ or CE\ going to H (data float): max. 10 ns (max. 20 ns)
inputs compatibility : 74F (74HCT)
outputs : 74AC (74HC)
Low voltage EPROM support from 2.5V if powered from external power supply.
Note.: values in parentheses are valid for 020/120 version

Relationship between supply voltage of EPROM in target device and equivalent speed.

Supply voltage	version 020/120	version 040/85
4.5V - 5.5V	120ns	85ns
3.5V - 4.5V	160ns	105ns
2.5V - 3.5V	200ns	125ns

POD protection circuit parameters

all pins are protected against Electrostatic Discharge (ESD) and balancing current
ESD protection rated to IEC1000-4-2 (15kV air, 8kV contact)
protection against balancing current up to 2.5A

SIMEPROM-02aLV operations

download
RESET control in target system

Buffer operations

view/edit, find/replace
fill/copy, move, byte swap, word/dword split
checksum (byte, word)
print

Supported file formats

unformatted (raw) binary
HEX: Intel, Intel EXT, Motorola S, MOS, Exormax, Tektronix, ASCII-SPACE-HEX
JEDEC

Download times

type 27020, parallel transfer, PC386/40MHz : 12 second
type 27020, serial transfer, 115200 Bd, PC386/40MHz : 28 second

PC system requirements

Processor: IBM PC AT or above, free 512 KB RAM
Operating system: DOS 3.2 or higher, Windows 3.x or Windows 95/98
FDD 3.5", hard disk with 2 MB free space
Free parallel (printer) port or free serial (RS232) port

General

operating voltage: external adapter 10VDC to 24VDC/4W or 5V +-10% from target system
power consumption: 350 mA max. (200 mA max.)
RESET forcing circuit: max. 20V, max. 100mA
galvanic isolation by serial line max. 250V DC
dimensions: 132x66x30 [mm] without cables attached
weight: about 150g
environment: office/laboratory
temperature: 5 to 40°C
humidity 20%..80%, non condensing
Note. value in parentheses is valid only for 020/120 version

Package included

SIMEPROM-02aLV simulator
SIMEPROM-02aLV, serial communication module (features optical isolation)
connection cable to PC for connection through parallel port and serial port
precise 32 pin socket, connected to simulator POD
precise 28 pin socket
precise 24 pin socket
wall-plug power supply 220VAC/12VDC, 500mA
user manual
3.5" diskette with software
"EQUIPMENT PROBLEM REPORT" and "DEVICE PROBLEM REPORT" forms
registration card
transport case

Simulator's price included too

free technical support (hot line)
free life-time software update via Internet

The information in this document are subject to change without notice.

SIMEPROM-01B

EPROM simulator

simulation of EPROM 2Kx8..64Kx8 (2716...27512), 120ns
low voltage EPROM support from 2.5V
output buffer powered from target system
connection to PC - parallel printer port
easy to use control program, DOS and Windows 95/98/Me/NT/2000/XP compatible

3 years warranty

SIMEPROM-01B is an EPROM simulator, designed for the development workplace, where are using EPROMs or PROMs. SIMEPROM-01B application is in the cases, where is emulator's use ineffective or impossible. Typical applications example of simulator EPROM are low-cost microprocessors system debugging, character generator in videocards/monitors tuning, etc. SIMEPROM-01B can replace EPROM from 2716 to 27512 with the access time above 120ns. Because output buffer of SIMEPROM-02aLV is powered from target system, there is possible to perform RESET of the target system by its power-off and power-on without problems. Quality of SIMEPROM-01B and negligible sales returns allows afford nearly lifetime - 3 years - guarantee for him.

Since SIMEPROM-01B simulator contains CMOS RAM, whose contents can be easily changed anytime, it can be replaced obsolete debugging cycle

switching off the target system

removing the EPROM from the socket

EPROM erasing

EPROM programming

inserting EPROM into the socket

switching on the target system
(about 20 minutes)

with much simple procedure

SIMEPROM-01B re-downloading
(about 3 seconds)

In addition, the SIMEPROM-01B enables the user forced the RESET signal on a device under development. Thus, a software can be debugged without handling the device.

SIMEPROM-01B interfaces with the IBM PC, XT to Pentium Pro, portable or desktop personal computers. Simulators allows you to directly connect to your PC through any standard parallel printer port (no special interface card needed). Using a Y reduction they are possible to connect two SIMEPROM-01B simulators to the same parallel port.

The SIMEPROM-01B simulator is controlled from the PC by the control program, which is common for all of the ELNEC's EPROM simulators. It is easy-to-use nice software with pull-down menu, hot keys and on-line help. The control program find himself type and port of connected simulator. Thus, it's possible connect all types of ELNEC's simulators on the same computer at the same time. User can doing

all necessary functions with simulator (download, RESET control)
with buffer (view, edit, fill, copy, swap, checksum, print)
read/write buffer in binary or wide range of HEX formats

Before exit of program, it can save all of the configuration for next use.

There are a BAT file version of control program, which can download of simulator content and can change the RESET status. For DOS operating system is available resident version of control program too.

Specification

Supported devices

EPROM/PROM: NMOS/CMOS, family 27xxx and 27Cxxx from 2KByte (2716) to 64Kbyte (27512) with 8 bit data bus
EEPROM: NMOS/CMOS, family 28xxx, 28Cxxx, 27EExxx from 2KByte (2816) to 32KByte (28256) with 8 bit data bus
EPROM/PROM/EEPROM from 64KByte to 128KByte with 16 bit data buss (2x SIMEPROM-01B with converter DIL40/DIL2x32 W-EPROM)

Compatibility

response on the address changed : max. 120ns
response on the CE\ signal going to L : max. 120ns
response on the OE\ signal going to L : max. 60ns
response on the either OE\ or CE\ going to H (data float): max. 10ns
I/O compatibility : 74HCT
Low voltage EPROM support from 2.5V if powered from external power supply.

Relationship between supply voltage of EPROM in target device and equivalent speed.

Supply voltage	Equivalent speed
4.5V - 5.5V	120ns
3.5V - 4.5V	160ns
2.5V - 3.5V	200ns

SIMEPROM-01B operations

download
RESET control in target system

Buffer operations

view/edit, find/replace
fill/copy, move, byte swap, word/dword split
checksum (byte, word)
print

Download time

EPROM type 27512, PC386/DX33 : 4 seconds

Supported file formats

unformatted (raw) binary
HEX: Intel, Intel EXT, Motorola S, MOS, Exormax, Tektronix, ASCII-SPACE-HEX
JEDEC

PC system requirements

Processor: IBM PC AT or above, free 512 KB RAM
Hard disk with 2 MB free space
Operating system: DOS 3.2 or higher, Windows 3.x or Windows 95/98
Free parallel (printer) port for connection of simulator

General

operating voltage: external adapter 7VDC to 24VDC/100mA or 5V +-10% from target system
power consumption: 80mA max.
RESET forcing circuit: max. 20V, max. 100mA
dimensions: 132x66x30 [mm]
weight: about 100g
environment: office/laboratory
temperature: 5 to 40°C
humidity 20%..80%, non condensing

Package included

SIMEPROM-01B simulator
connection cable to PC
user manual
3.5" diskette with software
"EQUIPMENT PROBLEM REPORT" and "DEVICE PROBLEM REPORT" forms
registration card
transport case

Simulator's price included too:

free technical support (hot line)
free life-time software update via Internet

The information in this document are subject to change without notice.

EPROM512 / EPROM020 / EPROM04 / EPROM080
Expandable ROM Emulator

Powerful & Less Expansive
Expandable & Extendable

No Add-On card necessary.
Download data from printer port. Suitable for PCAT, Apple Mac and any workstation with parallel printer port.
Expand from 8 bit environment to 64 bit environment just need 5 seconds. Suitable for 8 / 16 / 24 / 32 / 40 / 48 / 56 / 64 bit processors.
Extend from 27512 emulation to 27080 emulation just need to change the built-in memory chip.
Flexible download program available. Suitable for DOS/WINDOWS/UNIX system environment.
High bus width capability and high memory capacity. Suitable for advanced game program development and Mask ROM data pre-evaluate.

Application Feature:
No Add-On card necessary.
Download data from printer port. Suitable for PCAT, Apple Mac and any workstation with parallel printer port.
Power source can be from target board or power adaptor.
Expand from 8 bit environment to 64 bit environment just need 5 seconds.
Extend from 27512 emulation to 27080 emulation just need to change the built-in memory chip.
Flexible download program available. Suitable for DOS / WINDOWS / UNIX system environment. Support download function source program for user to develop their proprietary development environment.
Flexible and powerful ROM emulator for UNIX / XENIX system. Combined with GNU free software develop tools, would be a low cost advanced 16 / 32 / 64 bit RISC processor development system.
High bus width capability and high memory capacity. Suitable for advanced game program development and Mask ROM data pre-evaluate.

EPROM512 / 020 / 080 Specification:

Emulation capability
EPROM512 : 512Kbit (27512 - 2764) can be extended to 2Mbit or 8Mbit.
EPROM020 : 2Mbit (27020 - 2764) can be extended to 8Mbit.
EPROMO8O : 8Mbit (27080 - 2764)

Expand capability
up to 8 units daisy-chain together to be used in 64bit environment or emulate 64Mbit ROM environment.

Power consumption
Power from target board: +5V @ 0.25A(max.) or 0.15A(typ.) for each unit.
Power from adaptor: +9V or +12V @ 1.0A adaptor to support upto 8 units.

Access time
120ns.

Emulator probe interface
HCT244 compatible.

Environment
Operating temperature: 5? to 40?
Operating humidity: 10% to 90% RH
Storage temperature: 0? to 65?
Storage Humidity: 5% to 95% RH.

Options:
Emulator box: 15 x 7 x 2.3 cm. (EPROM512/EPROM020/EPROM080)
Power adaptor: +9V or +12VDC @ 1.0A. (PWR10)
28pin cable: 600mil DIP 28pin @ 30cm. (ROMC28)
Emulator 32pin cable: 600mil DIP 32pin @ 30cm. (ROMC32)
Printer cable to host: 25pin male to male @100cm. (ROMC25)

1 MB ROM Emulator & EEPROM Programmer

1. Supports PC / AT, 586 or compatibles.

2. Emulates ROM 27010 / 512 / 256 / 128 / 64.

3. Programs EEPROM 28010 / 512 / 256 / 64.

4. It is able to re-read codes and data from the Emulator board save on disk.

5, Parallel port interface, no additional card required.

6. The power of system is independent from computer.

7. Mini size, simple operation and low cost

1 MB ROM模擬器及EEPROM 燒錄器

1、適用PC / AT, 586或其他相容性電腦。

2、可模擬ROM 27010 / 512 / 256 / 128 / 64。

3、可燒錄EEPROM 28010 / 28512 / 28256 / 2864。

4、可回讀模擬器記憶體內的資料，並存放於磁片上。

5、使用印表機埠介面，免插卡，操作方便。

6、載入模擬器時間短，速度快。

7、筆記型電腦亦可使用。

8、使用獨立電源，不會破壞電腦。

9、體積小巧，攜帶方便。

10、附RESET信號輸出接腳，於程式載入模擬器後立即執行。

11、配件齊全，系統磁片(模擬及燒錄模式)與使用說明書。

ME-52 80C31/32, 8xC51 to 8xC58 Emulator made in China

Special offer for students and schools

採用專用"Bondout"仿真蕊片設計制造
實時仿真頻率高達33MHz, 仿真器提供12/24MHz時鐘信號
支持Idle和Powerdown模式
仿真器提供64K程序代碼存儲器, 支持仿真所有程序和數據地址空間
提供分辨率達一個字節的程序存儲器映像設置
64K硬件程序地址斷點和程序地址計數斷點
外部信號斷點
分辨率為1uS的實時效能分析
所有I/O均設有保護電路
支持仿真8XC51, 8XC52, 8XC54, 8XC58, 89C151/2051/4051
採用打印口高速并行通訊
尺寸: 176x122x26mm

集成開發環境

完美的Windows版集成開發環境MedWin
支持Franklin/Keil編譯, 連接工具
具有分別獨立控制項目文件的工程項目管理器
在工程項目管理下, 實現多模塊編程和混合語言調試
靈活的單模塊調試方式
VC++風格的窗口停駐, 窗口動態切分和工作簿模式窗口界面
十分強大的智能斷點設置和書簽功能
在線編輯, 編譯/匯編, 連接, 下載運行和錯誤關聯定位
符合編程語言語法的彩色文本顯示
完全底的表達式分析, 支持所有數據類型變量的觀察
無須點擊的感應式鼠標提示功能
MPA效能分析器
外設功能部件編程向導
不限制打開數據區觀察窗口的數目
調試狀態下用戶程序自動重裝功能
提供真實的軟件模擬仿真開發環境

ST-52 MPU-8051 / 52 & 8031 / 32 Emulator

* Emulate 8051 / 52 and 8031 / 32 ICs

* Supports PC / AT, 586 or compatibles.

* Program can be downloaded into the emulator via RS-232

* P0, P1, P2, P3 can emulate I / O while emulating 8051

* Does not occupy control port, interrupt, timer, ROM, and RAM

* Compatible with such compiler as XASM51, X8051, etc.

* 3 sets of memory setting:

1. external ROM 64K Bytes

2. external ROM 32K Bytes, RAM 32K Bytes

3. external ROM overlap RAM up to 64K Bytes

* 5V power source with mis - connected protection

* Two user selectable oscillator frequencies :

12MHz and 11.0592MHz,

* Also works as an EEPROM programmer.

* Reverse power input protection

* If the unit connects with the EX-51 board, it can carry out more experiments.

ST-52 8051 / 52 / 31 / 32單晶片模擬器

可模擬8051 / 52 及8031 / 32

程式完成後，透過RS-232做傳輸，免拆電腦

模擬8051時P0、P1、P2及P3都可模擬I / O

不佔用控制腳、中斷、計時器、ROM及RAM

適用XASM51、X8051等組譯器

記憶體可有三種設定方式：

1、外部ROM 64KBYTES

2、外部ROM 32KBYTES，外部RAM 32KBYTES

3、外部ROM與RAM重疊64KBYTES

可選用11.0592MHZ / 12MHZ或使用者自定的石英振盪器

適用於PC / AT, 586或其他相容性電腦

電源5V, 有反接保護

80C196KC Emulator

* Built-in lntel 80C196KC CPU, 5 I / O ports, 3 PWM outputs, 8 Bits A / D converter and UART port, and etc.

* 8 / 16 byte dynamic expandable memory circuit

* Flexible I / O pin array design for easy connection if used with standard ribbon cables

* Can be used as experiments :

LED display experiment

7-segment display experiment

buzzer testing experiment

8255 I / O expansion experiment

80C196KC模擬器

* 可由RS232將程式下載實習。

* 可完全模擬80C196KC高速輸出入( HSO & HIS ) 、

PWM與軟體TIMER。

* 附監督程式可在螢幕上顯示暫存器及記憶體內容。

* 可選擇8BIT或16BIT的工作模式。

* 適用於工業控制板基板或專題製作發展用。

* 具有基本的I / O實驗：

LED、開關、蜂鳴器。

21點的2003電流放大輸出。

DSP 56002 Emulator線上模擬器 (DSP-EVM)

* 可以完全模擬MOTOLORA 的DSP56002的晶片。

* 有線上組譯及反組譯功能。

* 記憶體最大為64K，程式記憶體及資料記憶體可以由使用者自行規劃。

* 有追蹤( TRACE )及單步執行的功能。

* 可以設定128個軟體中斷點。

* 有真實REAL-TIME的軟體中斷點。

* 多重記憶體顯示模式。

* 支援軟體在DOS下執行，附MOTOROLA原廠資料手冊

及說明書。

Doctor Z8 Emulator模擬卡

* 可模擬Z-8-MCU及部份Z8-CCP系列。

* 似DEBUG操作環境，易學易用。

* 線上ASSEMEBLY DISASSEMEBLY。

* 最大255步的單步執行。

* 全速即時( REAL TIME )執行。

* 可觀看及修改內部暫存器，內部RAM及使用者程式之內容 ( 包含MOVE, EDIT & COMPARE等命令)。

* 可設定4個中斷點。

* 程式執行中可任意中斷。

* 使用者程式的上傳( SAVE )與下載( LOAD )。

Introduction
Combine well performance and low cost, LEAP provides EPROM ERASER. LER-121A accommodates 12 devices (24-pin x 0.6"), and suits for small developing environment. Another modle LER-123A, of similar styling and
bigger size to the LER-121A, more extensive U-V tube and FIVE times the erasing area.That means the LER-123A can handle 64pcs of 24-pin x 0.6", suits for production line.

Feature
Equipped with electronic starter, extend the life of U-V tube
The timer can be set from 0 to 60 minutes
Powerful U-V tube, all ICs are ensure for maximum U-V exposure.
Protect users form U-V exposure by equipped with automatic U-V shut off switches when opening the device drawer
Have LED on the top panel to indicate U-V tube status
Provides almost completely erase area
Rugged metal construction but light as you can easy carry.

Standard Accessories
main unit x1
operation manual x1
DC power adaptor x1(121A) or power line (123A)

Back to top