VCM-100 Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 24 in Directly Single Mode / 255 in Binary Mode. *Input trigger modes: Directly Single/Binary/Direct cycle/ Parallel / Serial / Binary + Directly Single modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb/8Mb. *Max. Memory Capacity: 40 M-bits, (8M-bits x 5) *Total Time: 639 seconds (8KHz) Nice sound with 16KHz at least. : 319 seconds. *Supply Voltage: 12~36 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-100 is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant, random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a stand alone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

There are many Playback Modes: Direct Single, Direct Single of Cycle, Binary, Parallel and Serial modes. All of input modes setting by Rom-link Software Tool.

Direct Single Mode - Plays up to 24 sounds with individual trigger inputs.

Direct Single of Cycle Mode - Plays up to 24 sounds cycle with individual trigger inputs.

Binary Mode - Plays up to 255 sounds with binary code trigger inputs.(With strobe signal.)

Parallel Mode - Plays up to 255 sounds with binary code trigger inputs.(Without Strobe signal.)

Serial Mode - Plays up to 255 sounds with serial (RS-232/TTL LEVEL, n,8,1, 2400/4800/9600 BPS) trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold/Unhold, Normal/Interrupt.

General Specification

VCM-200 Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 8 in Directly Single Mode / 255 in Parallel Mode. *Input trigger modes: Directly Single/Binary/Direct cycle/ Parallel / Serial modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb/8Mb. *Max. Memory Capacity: 64 M-bits, (8M-bits x 8) *Total Time: 1022 seconds (8KHz) Nice sound with 16KHz at least. : 511 seconds. *Supply Voltage: 12~36 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-200 is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant, random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a stand alone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

There are many Playback Modes: Direct Single, Direct Single of Cycle, Binary, Parallel and Serial modes. All of input modes set by Rom-link Software Tool.

Direct Single Mode - Plays up to 8 sounds with individual trigger inputs.

Direct Single of Cycle Mode - Plays up to 8 sounds cycle with individual trigger inputs.

Binary Mode - Plays up to 127 sounds with binary code trigger inputs.(With strobe signal.)

Parallel Mode - Plays up to 255 sounds with binary code trigger inputs.(Without Strobe signal.)

Serial Mode - Plays up to 255 sounds with serial (RS-232/TTL LEVEL, n,8,1, 2400/4800/9600 BPS) trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold/Unhold, Normal/Interrupt.

General Specification

VCM-168 Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 28 in Directly Single Mode / 255 in Binary Mode. *Input trigger modes: Directly Single/Binary/Direct cycle/ Parallel / Serial / Binary + Directly Single modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb/8Mb. *Max. Memory Capacity: 24 M-bits, (8M-bits x 3) *Total Time: 383 seconds (8KHz) Nice sound with 16KHz at least. : 191 seconds. *Supply Voltage: 12~30 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-168 is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant, random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a stand alone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

There are many Playback Modes: Direct Single, Direct Single of Cycle, Binary, Parallel and Serial modes. All of input modes set by Rom-link Software Tool.

Direct Single Mode - Plays up to 28 sounds with individual trigger inputs.

Direct Single of cycle Mode - Plays up to 28 sounds cycle with individual trigger inputs.

Binary Mode - Plays up to 255 sounds with binary code trigger inputs.(With strobe signal.)

Parallel Mode - Plays up to 255 sounds with binary code trigger inputs.(Without Strobe signal.)

Serial Mode - Plays up to 255 sounds with serial (RS-232/TTL LEVEL, n,8,1, 2400/4800/9600 BPS) trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold / Unhold, Normal/Interrupt.

General Specification

VCM-60 Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 16 in Directly Single Mode / 255 in Parallel Mode. *Input trigger modes: Directly Single/Binary/Direct cycle/ Parallel / Serial modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb/8Mb. *Max. Memory Capacity: 16 M-bits, (8M-bits x 2) *Total Time: 255 seconds (8KHz) Nice sound with 16KHz at least. : 127 seconds. *Supply Voltage: 12~30 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-60 is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant, random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a stand alone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

There are many Playback Modes: Direct Single, Direct Single of Cycle, Binary, Parallel and Serial modes. All of input modes setting by Rom-link Software Tool.

Directly Single Mode - Plays up to 16 sounds with individual trigger inputs.

Directly Single of Cycle Mode - Plays up to 16 sounds cycle with individual trigger inputs.

Binary Mode - Plays up to 255 sounds with binary code trigger inputs.(With strobe signal.)

Parallel Mode - Plays up to 255 sounds with binary code trigger inputs.(Without Strobe signal.)

Serial Mode - Plays up to 255 sounds with serial (RS-232/TTL LEVEL, n,8,1, 2400/4800/9600 BPS) trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold/ Unhold, Normal/Interrupt.

General Specification

VCM-20S Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 8 in Directly Single Mode / 255 in Parallel Mode. *Input trigger modes: Directly Single/Binary/Direct cycle/ Parallel / Serial modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb/8Mb. *Max. Memory Capacity: 8 M-bits, (8M-bits x 1) *Total Time: 127 seconds (8KHz) Nice sound with 16KHz at least. : 63 seconds.(8mb x1) *Supply Voltage: 12 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-20S is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant ,random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a stand alone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

There are many Playback Modes: Direct Single, Direct Single of Cycle, Binary, Parallel and Serial modes. All of modes setting by Rom-link Software Tool.

Direct Single Mode - Plays up to 8 sounds with individual trigger inputs.

Direct Single of Cycle Mode - Plays up to 8 sounds cycle with individual trigger inputs.

Binary Mode - Plays up to 127 sounds with binary code trigger inputs.(With strobe signal.)

Parallel Mode - Plays up to 255 sounds with binary code trigger inputs.(Without Strobe signal.)

Serial Mode - Plays up to 255 sounds with serial (RS-232/TTL LEVEL, n,8,1, 2400/4800/9600 BPS) trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold/Unhold, Normal/Interrupt.

General Specification 

VCM-20 Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 4 in Directly Single Mode / 15 in Parallel Mode. *Input trigger modes: Directly Single/Binary/Direct cycle/ Parallel / Serial modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb/8Mb. *Max. Memory Capacity: 8 M-bits, (8M-bits x 1) *Total Time: 127 seconds (8KHz) Nice sound with 16KHz at least. : 63 seconds.(8mb x1) *Supply Voltage: 12 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-20 is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant, random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a stand alone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

There are many Playback Modes: Direct, Direct cycle, Binary, Parallel and Serial modes.

All of input modes Setting by Rom-link software tool.

Directly Single Mode - Plays up to 4 sounds with individual trigger inputs.

Directly Single of Cycle Mode - Plays up to 4 sounds cycle with individual trigger inputs.

Binary Mode - Plays up to 8 sounds with binary code trigger inputs.(With strobe signal.)

Parallel Mode - Plays up to 15 sounds with binary code trigger inputs.(Without Strobe signal.)

Serial Mode - Plays up to 255 sounds with serial (RS-232/TTL LEVEL, n,8,1, 2400/4800/9600 BPS) trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold/Unhold, Normal/Interrupt.

General Specification 

VCM-01 Digital Voice Module

Feature: *Operation Mode: playback only *Sampling Method: PCM / 8 bits *Sampling Rate:8K/11K/16K/22K/24K/32K Hz *Max. Sound Segments: 2 in Directly Single Mode. *Input trigger modes: Direct / Directly cycle modes *Memory Type: EPROM (27C0x0), 1Mb/4Mb. *Max. Memory Capacity: 4M-bits, (4M-bits x 1) *Total Time: 63 seconds (8KHz) Nice sound with 16KHz at least. : 31 seconds. *Supply Voltage: 12 VDC, 300mA *Output amplifier. : 3W (4 ohm load.) *Watch Dog Function. *Develop Software: VCM-Series Software Tools.

VCM-01 is a digital voice module .It directly plays back 8-bit mono PCM sound files digitized at 8,11,16,22,24,32 KHz. Sound files are programmed and stored in nonvolatile EPROM chips for instant, random access. There is no restriction on the length of each sound, as long as the total length of all sounds combined fit into the chips.

The board is designed to be a standalone device, powered by a single voltage supply. Sound playback can be triggered by a number of devices such as push button, motion sensor and dry contact closures. The built-in power amplifier can deliver up to 3W into a speaker, with adjustable volume control.

The board can be configured to operate in different modes. The configuration data is stored in EPROM chips along with sound bytes. On power up the board will configure itself automatically. There is no need to set switches manually.

Directly Single Mode - Plays up to 2 sounds with individual trigger inputs.

Directly Single of cycle Mode - Plays up to 2 sounds cycle with individual trigger inputs.

Every messages setting of attribute is independence.: Level /Edge, Hold/Unhold, Normal/Interrupt.

General Specification 

VCM-CF360 Digital Voice Module