PCI & IDE I / O Interface

W-3203-1P (1 port)
ENHANCED PARALLEL PRINTER CARD (16 bit)
FEATURES:
This model has one parallel port
SPP/BPP/EPP/ECP
Chips: A3203
Supports:
  • Standard Parallel Port.(SPP)
  • Enhanced Parallel Port.(EPP)
  • Enhanced Capability Port.(ECP)
  • Bi-Directional Parallel Port.(BPP/PS2)

Parallel Port can support products such as:

  • Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel port, SCSI adapter, External LAN adapter and Scanner.

Supports  IEEE 1248 standard.
 Each Port can select IRQ & Address as following:
 IRQ: 3,4,5,6,7,9,10,11,12,14,15
 Address: 378,278,368,268,358,258,348,248.
 DRQ: 0,1,2,3,5,6,7.(for EPP/ECP)
 Dack: 0,1,2,3,5,6,,7.(for EPP/ECP)
 16 BIT ISA layout

 

W-3203-2P (2 port)
FEATURES:
This model has one parallel port
SPP/BPP/EPP/ECP
Chips: A3203
Supports:
  • Standard Parallel Port.(SPP)
  • Enhanced Parallel Port.(EPP)
  • Enhanced Capability Port.(ECP)
  • Bi-Directional Parallel Port.(BPP/PS2)

Parallel Port can support products such as:

  • Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel port, SCSI adapter, External LAN adapter and Scanner.

Supports  IEEE 1248 standard.
 Each Port can select IRQ & Address as following:
 IRQ: 3,4,5,6,7,9,10,11,12,14,15
 Address: 378,278,368,268,358,258,348,248.
 DRQ: 0,1,2,3,5,6,7.(for EPP/ECP)
 Dack: 0,1,2,3,5,6,,7.(for EPP/ECP)
 16 BIT ISA layout

 

W-6535S-15/Serial/RS-232 Card (One Port) V4.1
W-6535S-25 2 Serial /RS-232 Card(Dual Port) V4.1
FEATURES:
Serial/RS-232: (W-6535S, W-6535)
  • Use UART FIFO 16C550(Default) or 16C650 or 16C850IC
  • 16, 32 byte transmit FIFO.
  • Each port has IRQ and Address multi select.
    IRQ: 3, 4, 5, 9, 10, 11, 12, 15
    ADD: 3F8, 2F8, 2E8, 3E8, 2F0, 3E0, 2E0, 260H. (COM 1,2,3,4,5,6,7,8)
  • Software select for 16C650 or 16C850IC. (Software Disk is optional)
  • Two Serial/RS-232 Ports:
    COM B connector uses DB 9 pin or DB 25 pin.(Default 9 pin)
    COM A connector uses DB 9 pin.
  • Clock: Uses crystal 14.7456 MHz (Default.)

JP23 is the Serial port speed and baud rate select.
COM A,B select as follows:
Speed Mode X'TAL BAUD RATE
1X 1.8432 MHz 115.2K=115.2K x 1
2X 3.6864 MHz 230.4K=115.2K x 2
4X 7.3728 MHz 460.8K=115.2K x 4
8X 14.7456 MHz 921.6K=115.2K x 8

 

W-6535-25 2S/1P Card
Features:
16BIT (V4.1)
Uses UART FIFO16550,16650 or 16750 IC

2S
IRQ:3,4,5,9,10,11,12,15
Address: 3F8, 2F8, 3E8, 2E8, 2F0, 3E0, 2E0 (COM1-COM8)
COM1-DB9 or DB25 (Default DB9) COM2-DB9
1P
SPP/BPP/EPP/ECP
IRQ:3,4,5,9,10,11,12,15
Support IEEE1284 standard
Address: 378.368.278.268.26C.27C

LPT1-LPT7

Centronic DB25 Female
1X 1.8432 MHZ 115.2K=115.2K*1 Default
2X 3.6864 MHZ 230.4K=115.2K*2
4X 7.3728 MHZ 460.8K=115.2K*4
8X 14.7456 MHZ 921.6K=115.2K*8

 

W-232 ISA Super I/O Card

Chips: Goldstar Prime 2C+75232 IC
 Supports 2 IDE/FDD(360K-1.44M)
 Supports 2S/lP/1G
 COM1-COM4(16450)
 LPT2-LPT3 (SPP)
 All Functions can be Disabled or Enabled
 Supports 2 IDE HDD
Supports 2 FDD (360K~1.44MB)
2S: 16C450, (3F8, 2F8, 3E8, 2E8)
         IRQ: 3, 4, 5.
 1P: SPP, IRQ5, 7 select.
 1G: One Game Port

w232h.jpg (12285 bytes)

 

W-2100-1P PCI One Port Parallel Card
1P:
  • One centronic port. SPP/PS2/BPP/EPP/ECP Mode
  • Data transfer rate up to 2Mb/sec
  • Supports DOS, WIN95, 98, NT

w21001p.jpg (29651 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes / second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
PARALLEL PORT FEATURES:
  • A3203 Chips
  • Supports:
    - Standard Parallel Port (SPP)
    - Enhanced Parallel Port (EPP)
    - Enhanced Capability Port (ECP)
    - Bi-directional Parallel Port (BPP / PS2)
  • The Parallel Port can support the extension of the following products: Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel Port, SCSI Adapter, External LAN Adapter, and Scanner.
  • Supports IEEE 1284 standard
  • DB-25 pin female centronic connector
  • P1 Print 1 is for the one parallel port

 

W-2100-2P PCI Two Port Parallel Card
2P:
  • One centronic port. SPP/PS2/BPP/EPP/ECP Mode
  • Data transfer rate up to 2Mb/sec
  • Supports DOS, WIN95, 98, NT

w21002p.jpg (30963 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes/second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
PARALLEL PORT FEATURES:
  • A3203 Chips
  • Supports:
    Standard Parallel Port (SPP)
    Enhanced Parallel Port (EPP)
    Enhanced Capability Port (ECP)
    Bi-directional Parallel Port (BPP / PS2)
  • The Parallel Port can support the extension of the following products: Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel Port, SCSI Adapter, External LAN Adapter, and Scanner.
  • Supports IEEE 1284 standar
  • DB-25 pin female centronic connector
  • P1 Print 1 is for the first parallel port.
  • P2 Print 2 is for the second parallel port.

 

W-2100-1S PCI One Port Serial Card
One Port Serial Card
  • One Port RS-232 / Serial
  • Data transfer rate up to 2Mb/sec
  • UART FIFO 16550 or 16650 or 16850 (default 16550)
  • Supports DOS, WIN95, 98, NT
 w21001s.jpg (30739 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes / second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
SERIAL / RS-232  FEATURES:
  • Uses UART FIFO 16C550 (default), or 16C650
  • COM A connector uses DB 9 pin
  • Clock uses crystal 14.7456MHz
  • Baud Rate: From 115.2K to 921.6K

 

W-2100-2S PCI Two Port Serial Card
2S:
  • Two Port RS-232/Serial
  • Data transfer rate up to 2Mb/sec
  • UART FIFO 16550 or 16650 or 16850 (default)
  • Supports DOS, WIN95, 98, NT
 w21002s.jpg (29698 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes/second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
SERIAL / RS-232  FEATURES:
  • Uses UART FIFO 16C550 (default), or 16C650
  • COM B connector uses DB 9 pin or DB 25 pin (default)
  • COM A connector uses DB 9 pin
  • Clock uses crystal 14.7456MHz
  • Baud Rate: From 115.2K to 921.6K

 

W-2100-1S1P PCI 1 SERIAL/1 PARALLEL CARD
One Serial / One Parallel Card
  • One Port RS-232 / Serial.
  • UART FIFO 16550 or 16650 or 16850 (default 16550)
  • One centronic parallel port. SPP/PS2/BPP/EPP/ECP Mode
  • Data transfer rate up to 2Mb/sec
  • Supports DOS, WIN95, 98, NT

w21001s1p.jpg (28972 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes / second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
SERIAL / RS-232  FEATURES
  • Uses UART FIFO 16C550 (default), or 16C650
  • COM A connector uses DB 9 pin
  • Clock uses crystal 14.7456MHz
  • Baud Rate: From 115.2K to 921.6K
PARALLEL PORT FEATURES
  • A3203 Chips
  • Supports:
    -Standard Parallel Port (SPP)
    -Enhanced Parallel Port (EPP)
    -Enhanced Capability Port (ECP)
    -Bi-directional Parallel Port (BPP / PS2)
  • The Parallel Port can support the extension of the following products: Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel Port, SCSI Adapter, External LAN Adapter, and Scanner.
  • Supports IEEE 1284 standard
  • DB-25 pin female centronic connector
  • P1 Print 1 is for the one port parallel card
  • P2 Print 2 is for the two port parallel card.

 

W-2100-2S1P PCI Two Serial/One Parallel Card
2S/1P
  • Two Port RS-232 / Serial
  • UART FIFO 16550 or 16650 or 16850 (default)
  • One centronic parallel port SPP/PS2/BPP/EPP/ECP mode
  • Data transfer rate up to 2Mb/sec
  • Supports DOS, WIN95, 98, NT.

w21002s1p.jpg (27572 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes/second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
SERIAL / RS-232  FEATURES:
  • Uses UART FIFO 16C550 (default), or 16C650
  • COM B connector uses DB 9 pin or DB 25 pin (default)
  • COM A connector uses DB 9 pin
  • Clock uses crystal 14.7456MHz
  • Baud Rate: From 115.2K to 921.6K
PARALLEL PORT FEATURES:
  • A3203 Chips
  • Supports:
    Standard Parallel Port (SPP)
    Enhanced Parallel Port (EPP)
    Enhanced Capability Port (ECP)
    Bi-directional Parallel Port (BPP / PS2)
  • The Parallel Port can support the extension of the following products: Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel Port, SCSI Adapter, External LAN Adapter, and Scanner.
  • Supports IEEE 1284 standard
  • DB-25 pin female centronic connector
  • P1 Print 1 is for the one port parallel card
  • P2 Print 2 is for the two port parallel card.

 

W-2100-2S2P PCI Two Serial/Two Parallel Card
2S/2P:
  • Two Port RS-232 / Serial
  • UART FIFO 16550 (default) or 16650 or 16850
  • Two centronic ports SPP/PS2/BPP/EPP/ECP mode
  • Data transfer rate up to 2Mb/sec
  • Supports DOS, WIN95, 98, NT

w21002s2p.jpg (26211 bytes)
FEATURES:
  • PCI Bus/32bit
  • PCI Specification 2.1. Compliant Target Interface Chip, supporting low cost slave adapters
  • Up to 5 local bus address spaces and four chip selects
  • Bi-directional FIFO for zero wait-state burst operation
  • PCI bus transfers up to 132Mbytes/second
  • Supports multiplexed and non-multiplexed 8-, 16-, and 32- bit generic local buses
  • Local bus runs asynchronously to the PCI clock
  • Supports Big/Little Endian byte conversion
SERIAL / RS-232  FEATURES:
  • Uses UART FIFO 16C550 (default), or 16C650
  • COM B connector uses DB 9 pin or DB 25 pin (default)
  • COM A connector uses DB 9 pin
  • Clock uses crystal 14.7456MHz
  • Baud Rate: From 115.2K to 921.6K
PARALLEL PORT FEATURES:
  • A3203 Chips
  • Supports:
    - Standard Parallel Port (SPP)
    - Enhanced Parallel Port (EPP)
    - Enhanced Capability Port (ECP)
    - Bi-directional Parallel Port (BPP/PS2)
  • The Parallel Port can support the extension of the following products: Tape driver, CD-ROM driver, ZIP driver, Printer, Parallel Port, SCSI Adapter, External LAN Adapter, and Scanner.
  • Supports IEEE 1284 standard
  • DB-25 pin female centronic connector
  • P1 Print 1 is for the one port parallel card
  • P2 Print 2 is for the two port parallel card.

 

W-2100-9705 PCI 1port Printer Card
Features:
Single 5-V Operation
Low Power
Multi-mode compatible controller (SPP, PS2, EPP, ECP)
Fast data rates up to 1.5 Mbytes/s (parallel port)
16 Byte FIFO
Software programmable mode selects
128-pin VQFP package

 

W-2100-9735 PCI + Dual UART and 1284 Printer Port
Features:
Single 5-V Operation
Low Power
PCI compatible Dual UART
16 byte transmit-receive FIFO (UART)
Selectable receive trigger levels
Programmable baud rate generator
Modem control signals
Status report capability
Compatible with 16C550,128-pin VQFP package
Multi-mode compatible controller (SPP, PS2, EPP, ECP)
Fast data rates up to 1.5 Mbytes/s (parallel port)
Fast data rates up to 1 Mbytes/s (serial ports)
On chip oscillator, 16 Byte FIFO (parallel), Software programmable mode selects

 

SCSI Interfaces

W- 801V75 Ultra Wide SCSI 3 Host Adapter
Features:
Fully PCI 2.1 compliant
Full 32-bit PCI DMA bus master
Provides Drivers for DOS, Windows 3.1/95/NT, Netware, OS/2 Warp, SCO UNIX, Linux, Utilities etc
Support of SCSI-1, SCSI-2 and Ultra SCSI (SCSI-3) protocols
Ultra Wide SCSI and up to 15 devices supports
Supports 536-byte DMA FIFO
Performs Wide Ultra SCSI synchronous transfers as fast as 40MB/s
Support Boot ROM

 

W-910U Ultra DMA SCSI Card
PCI Bus Master DMA
Up to 7 SCSI devices
Up to 133 Mbytes/sec (burst mode)
Up to 20 Mbytes/sec synchronous burst on the SCSI bus
DOS (version 4.0 and greater)
Windows (version 3.1 and greater)
Windows for Work Groups (version 3.14)
Windows NT (version 3.15,4.0)
Windows 95
Novell Netware (version 3.12,4.1)
OS/2 WARP (version 4.2 and greater)
SCO UNIX (version 1.2)
Interactive UNIX (version 4.0 and greater)
Linux (version 1.2)
Solaris(version 2.5)
Supports SCSI-1, SCSI-2, Interface

 

WPS-02 Parallel to SCSI-1
WPS-03 Parallel to SCSI-2
  • Works with all parallel ports including IEEE 1284 EPP and ECP ports(High Performance)
  • Converts the parallel port into a true SCSI interface in seconds
  • Transfer rates of up 2MB per second burst rate
  • Complete with install software for your SCSI perilpheral
  • Compatible with DOS, Windows, OS/2, Windows 95 and Windows NT
  • IEEE 1284 printer pass through maintains printing capability
  • Powered from SCSI device or optional 5V supply
 　

 

W-8210 ISA SCSI Card
  • Low-cost, high performance SCSI controller for non-bootable secondary SCSI devices.
  • MS-DOS/Win ASPI compliant driver, MPD for Win 95 and Win NT, OS/2 warp, SCO Unix.
  • 16BIT, ISA Bus (Pnp)
  • MSCDEX compliant CD-ROM drivers and MPEG1 drivers allow easy use in multimedia environment.
  • CE and FCC Class B Certified
  • Quarter-size low-profile PC board allows easy installation.
  • SCSI Protocol:SCSI-II CCS-4B (25 Pin connector)
  • SCSI transfer rate: 7MB/Sec.Asynchronous 10MB/Sec. Synchronous.

 

W-ISC-1 IDE To SCSI Card
FEATURES:
SCSI-2 and ANSI SCSI-3 Fast-20 StandardsSupports ANSI
High speed data transfer: SCSI Bus- Synchronous 20MB / S, Asynchronous 6.7 MB / S max.  IDE Bus- PIO Mode 4-16MB / S max.
Can convert IDE (ATA / ATAPI) device interface to SCSI
Supports all IDE / ATAPI devices: HDD, CD-ROM, CD-R, PD, DVD- ROM, MO, LS-120
SCSI / CCS compatible: Command set based on SCSI CSS Standard    (Rev. 5.B) Logical specification.   Data bus parity.  Arbitration
.Designed to work with devices with 5.25” bay sizes
Disconnect and Reconnect functions.
IDSC20A Chips onboard
Supports ANSI ATA-3 Standard
Compact design using IDSC20A IDE-SCSI Converter IC
　 SPECIFICATION:
DIMENSIONS: 126.31 mm (W) x 43.75mm (D) x 22.49 mm (H)
ELECTRICAL INPUT: +5 VDC 5%
POWER CONSUMPTION: 50mA (max. 400mA)
REPOOL:  5V 100m Vp-p                    
SCSI INTERFACE: SCSI-2 and SCSI-3 FAST-20, single ended type, 8 bit non-shielded 50 pin connector

SCSI CABLE LENGTH: 1. Other than FAST-20  MAX 6M       2. FAST-20 up to 4 devices   MAX 3M

INTERFACE: SCSI Bus (single engine, 8 bit.)  IDE Bus.  CPU Bus (type H8/3004).  ROM-Type CE.  Oscillator.  Voltage Management.

 

W-910UW PCI-Ultra Wide SCSI Card
Features:
Use Initio Ultra Wide SCSI controller chips
Supports Plug & Play, 64-bytes DMA FIFO.
Support 15 SCSI devices.
On board BIOS boot ROM.
Support 133Mbytes/sec. PCI burst mode.
Maximum transfer rate: 40 MB/sec. synchronous.
Programmable SCSI auto-termination
For Pentium/ Pentium Pro/ P55C/ Pentium II PCI bus system.
Provides Drivers for -- DOS, Windows 3.1, Windows 95/98, Windows NT, NetWare, OS/2 Warp, SCO UNIX, UnixWare.

 

W-930W PCI Ultra 2 SCSI Card
Features:
Use two Initio Ultra Wide SCSI controller chips
SCSI transfer rates from 5Mb/s aynchronous narrow SCSI to 80Mb/s wide LVD SCSI.
Burst transfer rates of 132 Mb/s.
Dedicated SCSI processor for handling SCSI operations.
Supports both auto and programmable SCSI termination.
Supports Command Tag Queuing, Sync./ Asynch. transfers, disconnects and reconnects.
SCAM Level 1 support and support for FLASH and Serial EEPROM device.
On board Scatter/Gather Cache and Intelligent Scatter/Gather Engine relieve on board processors from book keeping and enhance performance.
256 bytes data FIFO. 32 Command buffers on chip.
32 bits RISC handles all interrupts and command queue processing.
Supports Plug and Play to allow the user to change configurations without the use of jumpers.
Provides ASPI manager for DOS, Windows and Netware for third party applications.
BIOS supports DOS and Windows applications without driver
Dedicated caching logic to swap in and swap out Command Buffers.

 

Recovery Cards

W-R007 Recorvery Card
Supports DOS, WIN3.X, WIN95, OS/2, NT operating systems. Can run 386/486/586 personal computers.
 This Card can be easily installed. It has immediate Plug and Play, and no other driver is needed. Can support any disk copy function.
 After selecting the hard disk, for any FDISK/FORMAT/DELETE the computer can be restarted and all of the data will be recovered at a very high speed.
 If the computer has a virus, you just need to re-start the computer and the functions will be back to normal.
 Can select very many different recovery situations.
 Does not need IRQ select.
 Can select security password - e.g. one password for the teacher, and another for the sudent, or no password at all. The password can be changed at any time.
 If any kind of virus attacks the computer, the Recovery Card can recover from almost any condition.
 Supports 2.5GB HDD and upward.
 If CMOS has any problem, auto-recovery or no recovery can be selected.

W-R008 RECOVERY CARD
SYSTEM REQUIREMENTS:
  • HARDWARE:
    80386 IBM PC compatible or above.
    VGA Monitor, ISA BUS
    640K memory capacity or above
    One BIOS supported HD
  • SOFTWARE:
    One setup disk
    DOS, Windows 3.X, 9.X, NT, OS/2, 98 etc.

w-r008.jpg (8870 bytes)
FEATURES:
  1. Supports DOS, WIN3.X, WIN95, OS/2, NT operator systems. Can run 386/486/586 personal computer. This Card can be easily installed. It has immediate plug and play.
  2. As long as you have connected and installed the W-R008, you can press FDISK/FORMAT/DELETE and all of your data will be restored immediately after you reboot the system.
  3. Includes auto anti-virus intrusion without installing relevant software
  4. Administrator may modify HD protection and set multiple restoration modes.
  5. No occupation of IRQ or I/O port, and there is no conflict with other hardware.
  6. There is no need for disk configuration for plug and play restoration mode. Only a few simple installation processes will be enough to protect your computer system.
  7. You may adjust the occupancy of the HD volume as you desire, to maximize the efficiency of HD space while using plug and play restoration mode.
  8. With use of the W-R008 Hard disk drive guard, you can always recover your important HDD data, from almost any situation.
  9. This card is especially useful in a teaching situation, and allows all of the valuable data to be saved, and any student mistakes to be easily rectified. An administrators password can be used, to restrict unauthorized access.

 

W-R010 PCI Recovery Card (Lite version)
Features:
Plug and Play
Friendly interface designed for beginners
Instant restoring all of data when you restart the computer
No need to worry unexpected computer breakdown, system damaged and data lost
Least HD space occupation professional technical support
Suitable for any type of HD, Support HD 8.4G or above
100% Anti-Virus protector